Hmm..

Make sure you have ALL the ports suggested on this page.
http://support.microsoft.com/support/kb/articles/q278/8/87.asp

The thing is, each file transfer takes up a port, so, if you open 10 ports
then 10 transfers can exist, if you open 1, then 1 transfer can exist.

Tom.
----- Original Message -----
From: "Jithen Singh" <Jiriteach@hotmail.com>
To: "'Nik Kitson'" <nik.kitson@nz.uu.net>
Cc: "'ADSL Group'" <adsl@lists.unixathome.org>
Sent: Friday, November 30, 2001 9:32 PM
Subject: RE: MSN Messenger

> Hey Guys,
>
> I pinholed all those ports as you guys suggested and messenger is still
> unable to send files or have voice conversations. I can however receive
> files but the sending doesn't seem to work.
>
> Any other ideas guys ???
>
> Cheers
>
> Jithen
>
>
> -----Original Message-----
> From: owner-adsl@unixathome.org [mailto:owner-adsl@unixathome.org] On
> Behalf Of Nik Kitson
> Sent: Tuesday, 30 October 2001 11:35 p.m.
> To: 'Jithen Singh'
> Cc: 'ADSL Group'
> Subject: RE: MSN Messenger
>
> Assuming the your internal PC that has MSN running has IP address
> 10.0.0.1
> (change as necessary for your network), the appropriate ST Pro command
> line
> configuration is below.
>
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6891
> outside_addr=0
> outside_port=6891
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6892
> outside_addr=0
> outside_port=6892
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6893
> outside_addr=0
> outside_port=6893
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6894
> outside_addr=0
> outside_port=6894
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6895
> outside_addr=0
> outside_port=6895
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6896
> outside_addr=0
> outside_port=6896
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6897
> outside_addr=0
> outside_port=6897
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6898
> outside_addr=0
> outside_port=6898
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6899
> outside_addr=0
> outside_port=6899
> nat create protocol=tcp inside_addr=10.0.0.1 inside_port=6900
> outside_addr=0
> outside_port=6900
> nat create protocol=udp inside_addr=10.0.0.1 inside_port=6901
> outside_addr=0
> outside_port=6901
>
> Let me know if this works, and I can update my ST Pro pinholing FAQ to
> include this info.
>
> Cheers,
> Nik
>
> > -----Original Message-----
> > From: Jithen Singh [mailto:Jiriteach@hotmail.com]
> > Sent: Tuesday, 30 October 2001 22:36
> > To: 'Tom Picot'; 'Ben Milsom'; 'ADSL Group'
> > Subject: RE: MSN Messenger
> >
> >
> > Does anyone know how to do all of this stuff on the
> > speedtouch pro ? ..
> >
> > -----Original Message-----
> > From: owner-adsl@unixathome.org [mailto:owner-adsl@unixathome.org] On
> > Behalf Of Tom Picot
> > Sent: Tuesday, 30 October 2001 9:30 p.m.
> > To: Ben Milsom; ADSL Group
> > Subject: Re: MSN Messenger
> >
> > Hey Ben.
> >
> > A little reading and I found out that you need to open TCP port 1863,
> > however that will only open up messeging (which already works), so you
> > really need to skip this and read the following..
> >
> > To enable voice communications, make sure that outgoing TCP
> > connections
> > from
> > port 6901 are enabled. Also enable UDP packets where either the source
> > or
> > the destination port is 6901.
> >
> > To enable file transfers, enable both incoming and outgoing TCP
> > connections
> > to the 6891-6900 range of TCP ports. This allows each sender
> > to perform
> > up
> > to 10 simultaneous file transfers. Note that if only TCP port 6891 is
> > open,
> > users are only able to perform one file transfer at a time.
> >
> > Tom.
> > References:
> > http://messenger.msn.com/support/firewall.asp
> > http://support.microsoft.com/support/kb/articles/q278/8/87.asp
>
> The information contained in this email message may be confidential. If
> you
> are not the intended recipient, any use, distribution, disclosure or
> copying
> of this information is prohibited. If you receive this email in error,
> please tell us by return email and delete it and any attachments from
> your
> system.
>
> This message is part of the NZ ADSL mailing list.
> see http://unixathome.org/adsl/ for archives, FAQ,
> and various documents.
> To unsubscribe: send mail to majordomo@lists.unixathome.org
> with "unsubscribe adsl" in the body of the message
>
>
> This message is part of the NZ ADSL mailing list.
> see http://unixathome.org/adsl/ for archives, FAQ,
> and various documents.
> To unsubscribe: send mail to majordomo@lists.unixathome.org
> with "unsubscribe adsl" in the body of the message
>
>

This message is part of the NZ ADSL mailing list.
see http://unixathome.org/adsl/ for archives, FAQ,
and various documents.
To unsubscribe: send mail to majordomo@lists.unixathome.org
with "unsubscribe adsl" in the body of the message
Received on Thu Nov 1 07:54:25 2001