The Telecom ADSL network no longer supports the Speedstream 3020 card. It
only supports the 3060.

-----Original Message-----
From: owner-adsl@unixathome.org [mailto:owner-adsl@unixathome.org] On Behalf
Of Raimund Eimann
Sent: Wednesday, 1 September 2004 10:28 a.m.
To: adsl@lists.unixathome.org
Subject: Speedstream 3020 and Linux?

Hi,

I'd like to get an Efficient Networks "Speedstream 3020" card to run with my

SuSE 9.1 Linux. As far as I can see, Linux finds an appropriate driver
called
"lanai" for that card.

When I plug a telephone cable into the card, the LED on the back of the card

stays off (I would expect that the purpose of that LED is to show the state
of the DSL link and that would mean that within five minutes it should light

up...). Could this mean that this card is not usable in New Zealand?

I just append some output and hope someone will be able to help me...

The driver is running:

  # cat /proc/net/atm/devices
  Itf Type ESI/"MAC"addr AAL(TX,err,RX,err,drop) ...
[refcnt]
    0 lanai 000000000000 0 ( 0 0 0 0 0 ) 5 ( 0 0 0 0 0 ) [1]

But it doesn't seem to be used:

  # lsmod | grep lanai
  lanai 23424 0

And I can't see the card among the network interfaces:

  # cat /proc/net/dev
  Inter-| Receive |
Transmit
   face |bytes packets errs drop fifo frame compressed multicast|bytes

packets errs drop fifo colls carrier compressed
      lo: 100 2 0 0 0 0 0 0 100

2 0 0 0 0 0 0
    eth0: 131244 1546 0 0 0 0 0 0 493181

1153 0 0 0 0 0 0
    sit0: 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0

Some more information about the card:

  # cat /proc/net/atm/lanai\:0
  lanai(itf 0): chip=LANAIHB, serial=0, magic=0x5AB478D2, num_vci=1024
  revision: board=2, pci_if=0
  EEPROM ESI: 00:00:00:00:00:00
  status: SOOL=1, LOCD=1, LED=0, GPIN=1
  global buffer sizes: service=4096, aal0_rx=0
  cells in error: overflow=0, closed_vci=0, bad_HEC=0, rx_fifo=0
  PCI errors: parity_detect=0, master_abort=0, master_target_abort=0,
              slave_target_abort=0, master_parity=0
                       no_tx=0, no_rx=0, bad_rx_aal=0
  resets: dma=0, card=0

Cheers,
Raimund

-- 
This message is part of the NZ ADSL mailing list. 
see http://unixathome.org/adsl/ for archives, FAQ, 
and various documents. 
To unsubscribe: send mail to majordomo@lists.unixathome.org 
with "unsubscribe adsl" in the body of the message 
 
-- 
This message is part of the NZ ADSL mailing list. 
see http://unixathome.org/adsl/ for archives, FAQ, 
and various documents. 
To unsubscribe: send mail to majordomo@lists.unixathome.org 
with "unsubscribe adsl" in the body of the message